Details. You are purchasing a downloadable pdf of this standard covers the requirements for power tool cleaning of steel surfaces. Power too. SSPC-SP3 Power Tool Cleaning. Removes all loose mill scale, loose rust, loose paint, and other loose detrimental foreign matter by power wire brushing, power. SSPC-SP3 power tool cleaning is frequently used when contamination to adjacent areas is a concern by sandblasting (SSPC-SP 5 & SSPC-SP 10) or is not.

Author: Moogukree Mezishicage
Country: Lithuania
Language: English (Spanish)
Genre: Relationship
Published (Last): 28 April 2014
Pages: 240
PDF File Size: 5.68 Mb
ePub File Size: 17.99 Mb
ISBN: 482-4-89318-262-7
Downloads: 91831
Price: Free* [*Free Regsitration Required]
Uploader: Akinoktilar

Some coating specification requires a chloride test being performed before power tool cleaning even before solvent cleaning to identify the amount of deposited soluble salts.

Note that as supplements, every project will ssppc its conditions that need to be met. Subject Commentary Section Film Thickness I understand that you will use my information to send me a newsletter.

Besides, another benefit to using such aids is that it makes it easier to distinguish the difference between the various grades. Always note that using these references should never be a substitute to following the SSPC-SP 3 power tool cleaning zspc. Mill scale, rust, and paint are considered adherent if they cannot be removed by lifting with a dull putty knife.

SSPC-SP 3 Power Tool Cleaning

Please help us to share our service with your friends. RustPaintProcurementSafetyBusiness. We need your help! However, A uses the white metal blast as the surface preparation standard for repairing a zinc coating using sprayed zinc.

Grinding tools and impact tools are both acceptable means for achieving the level of cleaning specified.


A allows uncoated areas to be power-tool cleaned before repair with zinc rich paints in areas of less critical field exposure conditions. Although this method is convenient, it cannot be used to remove adherent forms of any rust, mill scale, and loose paint.

Use of this surface preparation standard roughens and cleans the bare substrate — including a hot-dip galvanized coating — to create a profile suitable for painting. The material provided herein has been developed to provide accurate and authoritative information about after-fabrication hot-dip galvanized steel.

If no arbitration or settlement procedure is established, then a procedure mutually agreeable to purchaser and material supplier or contractor shall be used. It is recommended, however, that the use of visual standards be made mandatory in the procurement documents.

Always blow off the surface with clean, dry, oil-free compressed air, brushing, or vacuum cleaning methods. I am at least 16 years of age. Intended primarily for carbon steel, but applicable on other metals, waterjetting does not create a profile on the metal substrate.

SP 3, Power Tool Cleaning

Power abrading tools also acceptably remove mill scale according to the standard. A provided definition of a brush-off blast cleaned surface describes a surface free of all visible oil, grease, dirt, dust, loose mill scale, loose rust, and loose coating when viewed without magnification.

The specifications for preparing hot-dip galvanized steel for paint and powder coating — ASTM D and D respectively — list hand tool cleaning as an acceptable method for smoothing the surface and removing zinc high sxpc of newly galvanized and partially weathered coatings. The standard also contains unique procedures for use on galvanized steel including inspection for a passivation treatment and wet storage stain.

TOP Related Articles  JRPRINT TO EPUB

The specification lists several different ways in which solvent cleaner may be applied to the surface including wiping or scrubbing the surface with solvent, spraying solvent directly onto the surface, vapor degreasing, ssc, alkaline cleaners, and steam cleaning.

What are these and which ones are important to the industry?

SSPC Surface Preparation Standards | American Galvanizer’s Association

Enter Your First Name optional. SSPC-SP2 Hand Tool Cleaning This standard covers the removal of loose mill scale, loose rust, loose paint, and other loose detrimental foreign matter from surfaces with the use of non-powered hand tools.

Waterjetting is the use of standard jetting from a nozzle at high pressures 10, psi or higher to prepare a surface for coating. It is highly important to note, although these aids sapc valuable, the written standards are ssc primary and hold the highest level of authority to meeting cleaning standard requirements. The power tools used for this standard include sanders, wire brushes or wheels, chipping hammers, rotating flaps, needle guns, hammer assemblies, and right angle grinders.

Methods of Power Tool Cleaning 5.

SSPC-SP 3 Power Tool Cleaning

Feathering the edges of adhered paint surfaces is also required. The preparation of a hot-dip galvanized coating for paint or powder coating connects this standard to the galvanizing industry. The degree of power tool cleaning required of SSPC-SP 3 ep3 based on the condition of the surface and also the new painting system.