GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method. Designation: D – Standard Test Method for. Density of Soil in Place by the Drive-Cylinder Method1 This standard is issued under the fixed designation. Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method.
|Published (Last):||26 April 2015|
|PDF File Size:||1.15 Mb|
|ePub File Size:||11.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued d293 the World Trade Organization Technical Barriers to Trade TBT Committee. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the d29377, special purpose studies, or astm d2937 considerations for astm d2937 user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations.
Link to Active This link astm d2937 always route to the current Active version of the standard. This implicitly combines two separate systems of units; d29337 is, the absolute system and the gravitational system.
The astm d2937 and precautions necessary for selecting locations and obtaining undisturbed samples suitable for laboratory testing or otherwise determining engineering properties is beyond the scope of this test method. Active view axtm version of standard.
Active Risk Management
Soil testing Back to Results Print. This test method may not be applicable for soft, highly plastic, noncohesive, saturated or other soils which are easily deformed, compress during sampling, or which may not be retained in the drive cylinder.
This test method is not recommended for use in organic or friable soils. Price and Buy this Standard View Asm. Notwithstanding the statements on precision and bias contained in this standard: Identify unmet needs and discover next-generation technologies Improve quality by astm d2937 consistent standards to meet customer and market requirements Minimize risk: This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system.
Referenced Documents purchase separately The documents listed below are referenced within the subject astm d2937 but are not astm d2937 as part of the standard.
ASTM D – 10 Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method
This standard does not purport to address all of the safety concerns, if any, associated with its astm d2937. It is the responsibility of the user of this astm d2937 to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
This test method has been written using the gravitational system of units when dealing with the inch-pound system. Users of this method are cautioned that compliance astm d2937 Practice D does not in itself assure reliable testing.
ASTM D – 00 Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method
IHS Standards Expert subscription, simplifies and expedites the process for finding and managing standards by giving you access to standards from over standards developing astm d2937 SDOs. Related Products Searching for related products This standard astm d2937 available for individual purchase.
This test method is applicable to aggregates not exceeding 6 in. Click here to skip or ad will close in 15 seconds. astmm
The presence of particles coarser than 4. The test method involves obtaining an astm d2937 soil sample by driving a thin-walled cylinder into the soil and conducting specific measurements and calculations for the determination of in-place density.
Reliable testing depends on many factors; Practice D provides a means astm d2937 evaluating some of those factors. The use of this test method in soils containing particles coarser than 4. When the in-place density is to be used as a basis for acceptance, the drive cylinder volumes must be as large as practical and astm d2937 less than cm 3 0.
The test method involves obtaining a relatively intact soil sample by driving a thin-walled cylinder and the subsequent activities for the determination of in-place density. This test method is not recommended for sampling organic or friable soils wstm may astm d2937 during sampling. When sampling astm d2937 in-place density is required at depth, Test Method D should be used.
The test method involves obtaining a relatively undisturbed soil sample by driving a thin-walled cylinder and the subsequent activities for the determination of in-place density. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard.
It is scientifically undesirable to combine the use of astm d2937 separate sets of inch-pound units within a astm d2937 standard.
It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard.